Smith's Products
Sealers
Poly-SEAL
With Semi-Gloss Or Low Sheen FinishProduct Quantity | 1 gal |
Colours | Gloss Or Low Sheen | Clear - WSC Color Packs Available |
Dry Time | 15-30 Minutes TF | 15-30 Minutes RC | 60-90 Minutes FT | 36 Hours HFT | 24 Hours FC |
SF Or LF | 225-275 | 250-330 SF |
Area Or Depth | Direct To Concrete /gal | 2nd Coat /gal |
Floor Or Wall | Floors & Walls |
Interior or Exterior | Interior & Exterior |
TF | Tack Free |
RC | Recoat |
FT | Foot Traffic |
LT | Light Traffic |
DT | Dry Through |
FC | Full Cure |
HFT | Heavy Foot Traffic (Forklift) |
VT | Vehicular Traffic |
FUT | Full Traffic |
-
Smith’s Poly-SEAL is a single component, fast drying, waterborne polyurethane polymer fused with a cross-inking acrylic which achieves a tenacious bond to approved substrates
-
HIGHLIGHTS: Ready-to-Use; Alkali-Resistant & Water Submersible; Fast Air Drying; Tenacious Bond to a Variety of Surfaces; Low Odour & Low VOC’s; Infinite inter-coat adhesion; Non-Chalking & U.V. Stable - Non-Yellowing; Good Blush Resistance; Resists to Hot Tire Pickup (Residential Traffic only)
-
RECOMMENDED USES: Primer for: Smith’s Poly-WB (Poly-SEAL Gloss ONLY over bare concrete). Seal Coat prior to high solids Polyurethanes for: Vinyl Chip Systems (Residential Garage floors only). Terrazzo Sealer*. Rockscapes. Bonds to: Concrete, Stucco & Polymer Modified Overlays; Pavers; Concrete Stains & Dyes (i.e. Smith’s Color Floor & Smith’s Liquid Dye);+ Terrazzo (Cementitious & Epoxy); Vinyl Chip (Neat, unsealed prior to topcoat of Smith’s Poly-WB)
-
LIMITATIONS: Do not use on non-porous surfaces, such as Ceramic or Porcelain tiles, Marble, Granite, etc. The specifier and user shall determine the suitability and assumes all responsibilities therewith; When applying solvent-based topcoats/sealers over Smith’s Poly-SEAL, apply an overnight cure to ensure all cross-linking occurs prior to solvent exposure; Avoid exposing freshly applied Smith’s Poly-SEAL to air movement, direct sunlight, freezing, water and direct sources of heat (i.e. radiant in-floor heat); For exterior, immersion, and wheeled traffic conditions, a minimum of an ICRI CSP 2 profile is required for mechanical preparation; NOT intended for use as a wood floor sealer; NOT for use in kitchen environments at risk of thermal shock
-
NECESSARY TOOLS & EQUIPMENT: Plastic Sheeting or Ram Board to cover floor for mix station; Paint stir stick; Premium, Non-Shed Paint Roller Covers (Roller Size Varies based on application); Paint Roller Frame with Extension Pole; Cleaning Solvent (Water While Wet);+ Masking Tape; Microfiber mop or T-Bar (for sealing Terrazzo only); Pump Sprayer or HVLP Sprayer *SEE SPRAY APPLICATION SECTION FOR MORE DETAILS (for exterior decorative concrete sealing)
-
APPLICATION METHOD: Apply via brush, roller, pump up, HVLP or airless spray which vary based on intended usage
-
APPLICATION TO STAINED CONCRETE: After allowing a full cure* (minimum 12 hours) time for Smith’s Color Floor, Color Wall or Color Accents, remove all loose particulate utilizing a leaf blower. If standing water is present, remove excess water with a cloth or squeegee. Allow the substrate to dry before application of Smith’s Poly-SEAL
-
Low Sheen | Safety Data Sheet | SDS
Download PDFGloss | Safety Data Sheet | SDS
Download PDFTechnical Data Sheet | TDS
Download PDFVisit Smith's Website
Visit Website